Overclocking problem?
"Safe" is relative to what you consider to be safe... As far as increasing your voltage to the CPU I'd go with the smallest amount your bios allows... (Like 0.5v or less) Then after increasing the voltage...test a small frequency speed increase as well...Run some benchmarks to see if there's any improvement at all...There's no sense in cranking the CPU frequency up higher if its not improving upon the performance...Make sure to watch the HEAT closely as well...(Motherboard Monitor if you don't have onboard temp monitors) Keep in mind doing any of this Voids your Warranty! Do all you CPU overclocking first...then move on to your memory...Setting memory timings (tightening up the memory timing) can be tricky and make your computer unbootable to the OS...so don't do this without knowing what you're doing... You could simply increase the FSB...this will overclock your memory and the CPU as well as over all increasing of you bus speeds...... There's lots of ways of doing this...Do A LOT of Research on your particular system and mobo to get best results...
FL studio sound problem (Wind sound)?
I have this weird problem with fl studio 10. When i use wind sound with 3xosc with a kick the sound gets rly "irregular". Its like the volume gets up and down irrelugary when the kick and wind sound plays together. Im using a steinberg ci1 interface soundcard with my pc. Any ideas? Heres a link where u can download an example of the problem (Wav file). I would really appreciate if someone could help me out with this problem its really irritating! Tell me if the link doesnt work. http://www.2shared.com/audio/0Fw6kGFc/Problemintro-4.html
Is the problem in my PC or compiler?
When making questions of this type, you should always explain HOW it's not working. It's also a very good idea to give at least a basic description of your build environment, such as which operating system you're using.Doesn't it compile?Does it segfault when the line is reached?Does the computer hang?Does it merely jump past the line without any apparent effect?Does the linker complain?I'm guessing you experience #4, but it's impossible to tell from the question itself."system" invokes a new program, similar to if you ran it in a shell (in Linux e.g. you could write 'system( "ls -l /home" );'. If "pause" doesn't exist in the known paths of your system, the call will fail.
Is DNSBlock Harmful? Do You Have any Ideas to Remove it from PC?
It's the same as DNS Unlocker.To remove it, follow the steps here:How to Remove DNS-Unlocker Adware (Removal Guide)
If i factory reset my windows 7 pc will all the problems i had the past couple of days disappear?
Maybe.I have no idea what all your problems *really* are. What I do know, is that progressively speaking, every time I hear about you and your computer issues, the list of issues keeps growing. I mean, I answered a question regarding the problem with Userinit.exe and/or Windows Shell not loading properly... and now I find you've deleted necessary system files? What's next, warnings about your cooling fan not working? Warnings about your hard drive dying? Are you going to ask how you perform a factory recovery on your unnamed mystery make and model laptop/desktop computer? Are you going to ask how you reinstall Windows when you don't have any installation media, and your recovery system doesn't work?Then... there's the distinct possibility that your problems are going to continue as soon as you finish the factory recovery.... because you will go right back to the same websites you went to before that resulted in the infections that started this mess. That will bring the problems right back to you.Will performing a factory recovery solve the problems you listed above? Yes. Will you have to use the recovery media instead of the recovery partition or information on your computer? I have no idea. Will your problems return? I have no idea.
I'm installing iAtkos v7 Mac OS X leopard on my PC.Just 1 problem I can't figure out..?
I am installing mac OS X leopard 10.5.7 on my PC. It loads just fine error free up until the installation where i select language and click next, etc. When it gets past the BIOS part to the installation my mouse and keyboard quit working. This also happens when in the windows xp setup. They both work in the BIOS when booting and pressing F8 and such but as soon as it gets to the setup the numlock light turns off and the keyboard quits working and the laser on the mouse turns off and I can't click or press anything. They are USB mouse and keyboard. I do not have a ps2 of either or an adapter. They work in ubuntu setups and vista setups so idk what the problem is. Any ideas?
I am having problems connecting nokia 63210i to my pc either by cable or bluetooth. any ideas?
make sure your computer has bluetooth on it, then make sure its on then use your comp and "search for devices" and it should find the phone as a bluetooth device, if not then try google for the driver for your nokia phone
Today I had a Blue Screen of Death experience with my PC. My computer has been showing signs of slow performance, but I did not have any idea about what to do about it. Now, I have to do something. Can I bring it back to life after the BSOD?
BSOD isn't as bad as it sounds. You can bring it back to life! There are several issues that may cause this error and you just need to be able to scan your system registry to find the problem. There are some good registry cleaning software programs that can do this for you. I use PC Healthboost to do a regular system scan and make sure there aren't too many invalid or corrupted files accumulating in my hard drive. It's a cheap and easy way to keep the problem from reoccurring again. You may also choose to look into the problem further by reading up on the issue. Forums like this one are good for that, and Windows has a number of good user forums. Good luck.
So I recently purchased Lenovo 710 ideacentre desktop. HDMI output not working. I ve been updating my computer for the past hour. Any ideas?
So I recently purchased this desktop. I noticed the hdmi output doesn t work with my hdtv using an hdmi cable. I ve tried multiple cables, different hdmi ports on tv, and made sure I was on the right input. But my tv still shows "no signal." I ve tried using a monitor via VGA and using the hdmi cable to the hdtv at the same time in hopes of having dual screens. The VGA works fine, but hdmi doesn t. Does anyone have any suggestions or had this problem before? Maybe I need to return the computer for a new one? Thanks for your input.