Where is the ethernet port on Acer Aspire?
Many members of the Acer Aspire series, such as the V5, are too thin for an Ethernet port and instead use a proprietary connector. That port on the side near the HDMI port and it provides Ethernet and VGA through a special adapter. The adapter comes with the laptop, but many people end up misplacing it or forgetting to provide it when selling the unit to someone.My Aspire uses the LAN/VGA Combo Port Cable (Part # AK.LAVGCA.001)Newer units may have a MiniCP port instead, which uses the Acer Converter Cable (Mini CP to VGA/LAN/USB) (Part # NP.OTH11.00C)
Mac or PC for university?
I am looking for a laptop computer that would last for approximately 4 years and still be in good condition. It should be able to deal with all of the assignments, internet use, as well as wear and tear that goes along with a post secondary education. It should have a dual processor and preferrably more than 1GB of RAM. Is a mac better or a PC? What specifications am I looking for? Which PC brand is best? Which Macbook is best? Why? Money is no object (to a reasonable degree). Thanks!
How do I connect Bluetooth speakers to my laptop?
Answer taken from How to connect my Bluetooth speaker to my laptop - Driver EasyPrep work: check my laptop Bluetooth settingAll the screenshots shown below are from Windows 10, but the steps work in Windows 7 too.1) On your keyboard, press the Windows logo key, and type network. Click Network and Sharing Center.2) Click Change adapter settings.3) The Bluetooth Network Connection shows you have Bluetooth on your computer.4) If the icon is grayed out, right click on Bluetooth Network Connection, and click Enable.Don’t worry if you don’t see Bluetooth Network Connection. You can buy a USB Bluetooth receiver and plug it in any free USB port on your computer.Connect my Bluetooth speaker to my laptopMake sure your Bluetooth speaker is within the right distance (often 10 meters) from your laptop.I’m using Windows 10I’m using Windows 7I’m using Windows 101) On your speaker, press the Power button, then press the Bluetooth button to make it discoverable.The method to make your speaker discoverable may vary. Your can check the manual if you have any doubts about it.2) On your computer keyboard, press the Windows logo key and type blue. On your screen, click Bluetooth and other devices settings.3) Make sure the switch says On (if it says Off, click the switch). Click Add Bluetooth or other device.4) Select Bluetooth.5) Click the name of your speaker, and then click Pair.The two devices should have connected successfully. You might also need to follow the on-screen instructions to complete the pairing process.I’m using Windows 71) On your speaker, press the Power button and the Bluetooth button to make it discoverable.The method to make your speaker discoverable may vary. Your can check the manual if you have any doubts about it.2) On your computer keyboard, press the Windows logo key, type add and click Add a device.3) Click the name of your speaker and click Next.The two devices should have connected successfully. You might also need to follow the on-screen instructions to complete the pairing process.
How do I turn on a laptop without a power button?
I'm presuming that its a hardware fault which needs you to power up your laptop without using the Power button.I guess, your power button is no longer working.If you can open up the laptop, and get to the power button, you can observe that its nothing, but a puch button that completes an electrical circuit. This acts as a signal for the internal controller to understand that the power button is pressed.Now, if my memory serves me right, I saw an answer somewhere by Adrián Lamo, how he, at some point of time, had his Laptop or PC (I do not remember correctly) completely open, like skeleton, all organs and the skin separated. He just made the two wires on each side of the Power button to touch each other, and act as the appropriate signal.If you're okay with that, and feel confident enough about opening up your laptop, go ahead, open it up, Attach two wires, one wire on each connection, and take them outside, then, stick them together with some sticky tape, and whenever you need to press the power button, just short those two wires.And, just in case you don't feel confident and/or okay with the idea of shorting two stupid wires sticking out from your Laptop's power button hole, spend some money, and get the Power button replaced. I'd prefer the first choice. one can hide the wires into a USB socket, on opposite sides, and whenever you plug in a USB device, the outer metallic part makes a short between the two wires. Just, don't use that USB port for anything else. (It might be also mis-interpreted as a Long press.Jokes aside, Go and get it repaired.
What can I do if my HP laptop can't detect the WiFi and wire connection?
Step 1:Check your Wireless connection is enabled or not. Open RUN (Windows Logo + R) and type type “ncpa.cpl” and press Enter.Step 2:On Network Connection, find your Wireless and check it. If it’s disable, then right click on your Wireless and click Enable.Step 3:If still your WiFi not working, then follow step continuously.Step 4:Open RUN and type “devmgmt.msc” and press Enter to open Device Manager.Step 5:Now find and expand Network adapters.Step 6:Now right click on your Wireless network and click Update Driver Software.Step 7:Click “Browse my computer for driver software“.Step 8:Click “Let me pick from a list of device drivers on my computer“.Step 9:Select your Wireless Network Adapter and click Next.You will see the update driver successful dialog box. That’s it, now check your WiFi. If still not working, then follow steps continuously.Step 10:Unplug your Wireless for 1 Minutes and restart it.