Ford fiesta problem help me to solve this problem.?
hello everyone. i have a ford fiesta 1.4 ghia 2002 with 95000km. first the car run ok very good now from 2 days it showing me EAC fail and if i start again the engine light on and it on and off again after 2 sec. but when i on it again and if i give some accleaction like 2000rpm it dont go off but as i leave it off again. if any body know what is this please help. thank you
1999 ford fiesta radio wiring?
Ground (Chassis) Brown +12 Supply Red Accessory On Yellow Ignition On Black Illumination Grey / Yellow Power Antenna Blue Front Left Speaker + Yellow / Black Front Left Speaker - White / Black Front Right Speaker + Yellow / Brown Front Right Speaker - White / Brown Rear Left Speaker + Yellow / Green Rear Left Speaker - White / Green Rear Right Speaker + Yellow / Red Rear Right Speaker - White / Red All I could find. Use a meter to verify before making any connections.
How do I fix my Ford Fiesta heater from only blowing cold air?
It is probably the temperature blend door actuator. If you change the temp setting and hear a clicking/popping noise in the dash, it is either the actual blend door or the blend door actuator. Other possible causes are the switch, wiring between the switch and actuator, or an engine coolant issue (low coolant level or heater core blockage).
Can i put electric side mirrors on my ford fiesta mk5?
You can do it. I have some on my 1997 Ford Aspire. And it didn't even come with them period. You will have to find the mirrors and figure out if you will have to mod anything for them to fit. (You never know). You have to also make sure is there a spot for the control switch for it. Otherwise, woo drilling! But you will also need a power source to run to the motor and the control switch. All i did was fab the mirrors to fit, put in the control switch in the door panel armrest. And put up a source of power. It would be good to put a at least a fuse on it because if it shorts out, It won't short your whole car. I also have installed power windows and locks in my Ford Aspire too so anything is possible with a little time and work. Well i hope this helps and good luck! Also, You wont need to change your wiring harness. It is like installing the fog lights in my car, All it is, is a control switch, and a motor. I put a source or power to the switch. And the switch to the motor. You don't need to mess with the computer. Not with mirrors that old anyways because the mirror knows what switch does what.
Ford Fiesta (x reg) chugging when going and revved low?
I have a X reg Ford Fiesta 1.25, 16 vale. The car started chugging when driving, also chugs when in neutral and revved low just over 1000 rpm and the engine management light has come on I have checked the oil and water and were low but now topped up but still chugging any ideas????
How do I replace the rear wiper blade on Ford Fiesta?
If the old plastic piece is fixed to the wiper arm you should be able to replace the blade without the new parts. There are two basic types. the first is a wiper that clicks onto a pin. if its that type there will be a small button on top of the wiper. press the button and remove the wiper off by pushing it away from the arm. The other type has a hook type attachment. There could be a button on top or underneath inside the wiper on this type. Locate the button and pull the old wiper off by sliding it back toward the wiper motor. To put them back on just push on until they click into place. Most of the time the new plastic pieces are not used. They are in there just in case.
03 ford windstar won't move once put in gear?
I have on '03 ford windstar that will not move once you put it in gear. the gear shifter flows freely and i've not had any problems with it skipping gears or reving up while shifting gears. yes i have checked the transmission fluid and it isn't burnt and is full (been asked that question 500 times). so what could possible be the issue, i'm praying that we don't have to replace the transmission there's been no issues until today and just went ca put suddenly without warning. it is 87000 miles on it roughly. only serious answers please, and no criticism please. thanks
Need help connecting Dual XDVDN9131 player in 1999 Ford Expedition?
i have a dual xdvd8181 in a ford ranger and its a fairly simple installation. first you will need to get an adapter/installation kit for your specific year expedition. then you will also need to get a wiring harness for your expedition. both of these can be gotten from an electronics store such as electronic express or many retail stores like wal-mart. both the installation kit and wiring harness will have detailed instructions with them as to their application. you will simply follow these for your particular application. you will also need to get a ford radio extraction tool availiable at wal-mart to take the old radio out. the only thing with the flip out dvd screen is the safety feature ground wire that prevents your screen from playing video when the emergency brake is not set. there will be a diagram of how to hook this wire up in your install manual that came with the dual xdvd cd/dvd/mpe3 player. mine is actually hooked up to a toggle switch and a separate ground but this application is best done by someone with a little more experience. i would just stick to the diagram in your xdvd manual for the safety ground hook up. you can attatch your wires to your wiring harness with solder, with crimp connectors or with a simple twist and tape method (not reccomended). hope this helps. goood luck.