Can you make an Ouija board out of paper? How can you get rid of one?
Important Things To Remember: - It is ok to make your own board, it works just the same, perhaps even better because it would be filled with your own energy! Choose a wood like birch or oak. A good board size is fifteen by twenty inches and at least a quarter of an inch thick to resist warping. Sand, stain and letter your board then coat it with clear lacquer or enamel. Feel free to embellish it with images of suns, moons, stars, pentagrams. Make the planchette out of wood or clear plastic. You might of course want to use a glass or a cup, in that case remember to hold them over candlefire before each session. - Limit the experience to 3 hours a week or else you'll become an addict and consequently a slave to certain spirits. - Cast the Circle before the session and close it afterwards. If you're Christian, keep a rosary close at hand. - NEVER leave the planchette (message indicator) on the board if you aren't using it. - If the planchette goes to the four corners of the board or repeatedly makes a figure eight, it means you have contacted an evil spirit. In these cases, quickly turn the planchette upside down and use it that way. - If you feel anything threatening say goodbye and put the board up immediately. - If you ever want to get rid of your board, DO NOT BURN IT! Break it into seven pieces, sprinkle it with Holy/Consecrated Water then bury it.
Good Topics For A Religion Research Paper?
I'm think of doing a research paper on either: Sciencetology Demonology Souls Chinese Zodiac these are just some, if you can think of any more can you let me know?
Can you get fingerprints from paper?
What an interesting question and the short answer is "yes". There are at least two methods of lifting fingerprints from paper. The first uses "rubber-gelatin lifters", which are suitable for textured surfaces because of their thickness. The problem with paper is the uneven surface - a fingerprint on paper becomes visible when brushed with powder, but regular tape-lifters do not come in contact with the powder that has landed in the deeper parts of the paper, and so the lifted prints will be missing some details. Rubber-gelatin lifters are thick and are able to get down into all the inner recesses and form a sort of "cast" that can then be lifted off the paper as a whole. The second method consists of fuming the prints with Cyanoacrylate (Super Glue), dusting with powder, and then lifted using lifting tape. Rubber-Gelatin Lifters "These rubber-gelatin lifters are especially developed for the lifting of fingerprints, footprints, dustmarks and micro traces. The thick, non-aggressive, low-adhesive gelatin layer permits the lifting of traces from almost every surface, including porous materials, such as paper or cardboard. Lifted prints can be collected for photography or closer examination. http://www.redwop.com/technotes.asp?ID=9... Fuming with Cyanoacrylate (Super Glue™) "Most latent prints developed with glue fuming will have white ridges and will be quite noticeable. Sometimes, however, the latent prints will be very difficult to see; therefore, each piece of evidence must be carefully inspected. Oblique lighting from a flashlight will be helpful. It is suggested that these prints be photographed before other processes are used. The latent prints can be visually enhanced by dusting with regular or magnetic fingerprint powder contrasting with the background. Once dusted with powder, glue-fumed latent prints can sometimes be lifted with regular lifting tape. The latent prints are quite durable and usually can be lifted more than once. Sometimes the second lift is clearer than the first. http://www.redwop.com/technotes.asp?ID=8...
Made my own ouija board, nothing happened?
I made a homemade one. It was on the back of a notebook with lined paper in it, it was cardboard. I wrote out Yes, No, etc. got my Rosary beads, started with a nice saying to let them know I was there.... nothing happened. So I used the following items as the panchet (the pointer, i think panchet is it's name....) a quarter, a dime, a quitar pick, a paper clip and my student id card. all of these items can easily slide aross the cardboard, because they are light andd smooth and so is the cardboard. also, it was around 4 in the afternoon.... so what did I do wrong? Any suggestions to help me get better at this? If you don't believe in ouija boards, can you explain why and can you explain the ideomotor effect to me? also I'm an amateur at communicating to the dead, but I'm really into this, so no mean comments please thanks:)
How do I write a letter to the principal for not submitting an assignment within time?
To,The PrincipalABC collegeDate:Sub: requesting for allowing to submit the assignment after the date of submission.Sir,With due respect, I want to state that I am a student of class ____ of your college. I had to submit an assignment on “____” for my paper ____, before the date ___. But as I was suffering from illness/ was busy in some important works, I was unable to submit my assignment on time.I, therefore, request you to be kind enough to allow me to submit my assignment, as it is very much essential/ compulsory for completing the degree.Thanking youYours faithfullyName:Class:Roll No.:_____________