Is it safe to drive a vehicle without power steering fluid?
No it’s not. While you CAN drive without it, the potential failure could result in stranding you on the side of the road. Anything built in the last 15 years most likely has a serpentine belt system that powers all your accessories.When you run out of power steering fluid, the bearings in your power steering pump no longer have lubrication available to keep them cool. Those bearings will fail, the pump will seize and that will result in your serpentine belt to fight against one accessory that is no longer moving. The belt will fly off the engine and all other accessories, water pump, A/C, alternator etc will be powerless and your vehicle will shortly cease to run from overheating or dead battery.
What are some of the things that can happen if I keep driving my car with a broken tie rod?
Tie rods have an adjustment that keeps your tires in alignment. They also provide the link between your steering wheel and the front tires. You turn the wheel, the tire rod pushes the tires left and right.Worn tie rods can cause shaky front wheels, misaligned front tires, imprecise steering, excessively worn tires. A broken tie rod would allow one tire to flop to the side causing instant loss of steering and a crash if you are going fast enough.A least, you will be wearing out your tires much faster than you should. You will be replacing those tires sooner than later.At most, a worn tie rod could cause an accident because your steering isn’t accurate.If you are still driving your car, you don’t have a broken tie rod. You may have severely worn tie rods if your front tires are wearing unevenly (can be caused by a poor alignment as well), aligning the front end doesn’t fix your tire wear problem, or your steering wheel wobbles while you drive.They aren’t that expensive to replace and much less expensive than adding a new set of tires to that cost or an accident.
Why is my car shaking and the check engine light flashing?
A shaking vehicle AND flashing MIL ("check engine light") sound like the vehicle is misfiring on at least one cylinder. As @Anna Nguyen, @Brendan Sinclair, @Antoun Nabhan and others have said, it could be an ignition related problem. It could also be fuel-related. If one or more fuel injectors are clogged or dead, that would also cause a misfire in the affected cylinder(s). These are relatively cheap/easy things to check and fix.Other causes (which could be more complicated and more expensive) to fix include contaminated fuel, a bent intake or exhaust valve, a broken valve spring, a damaged piston/connecting rod, and on and on.I recommend getting a scan tool and checking the codes which are causing the MIL to light/flash and I also strongly recommend NOT driving the vehicle until the problem is fixed. If you continue to drive the vehicle as is, you will exacerbate the problem. Dumping unburned fuel into the exhaust due to a misfire will overheat and kill your catalytic converter. A more serious problem like a bent valve can eventually cause you to crater your engine (i.e.: completely destroy the engine).
What are the symptoms of a bad inner tie rod?
Symptoms of tie rod failure can include clunking or clicking when turning the wheel or while traveling over a bumpy surface, noticeable steering slack (moving the steering wheel left to right when the wheels are straght), vibrations when driving, reduced turning radius either left or right and a simple way of checking for wear is to turn the wheels to the left of checking the left wheel and to grab the tie rod with both hands and to move it about. If it moves freely then it needs replacing, if not fixed soon complete tie rod failure would release either wheel from any steering input leaving you stranded and in a dangerous situation if it fails at higher speeds.
What are some symptoms of too much transmission fluid?
Excess transmission fluid will cause foaming in any transmission. Foam does not flow like oil, reducing cooling and lubrication. It also implodes on compression between gears or in the hydraulics of automatic transmissions, causing severe damage (pitting).In an automatic transmission, you will have higher temperatures and poor shifting, as it depends on solid hydraulic pressure, not spongy foam to move the clutches and bands.Automatic transmissions with dip sticks should be measured with the engine running, and consider the operating temperature. Note here how the heat affects the measurement. It should not be filled to the top when cold, or checked not running.If it does not have a dipstick, it is measured with the plugs on the side, depending on specific instructions per brand of car.Manual transmissions normally don't have dipsticks (some do). They are checked from a plug on the side of the transmission, and the level should normally be at the level of the plug, not above.