HELP MY SANDISK MEMORY CARD IS SAYING FILE CORRUPTED AND UNREADABLE..WHAT CAN I DO TO RECOVER THIS?? HELP!?
I SAW MY PICTURES AND I WAS JUST ADJUSTING THEM TO BE RIGHT SIDE UP SO I CAN UPLOAD THEM AND THEN ALL OF THE SUDDEN WHEN I TRIED TO TRANSFER THE PICTURES OVER TO A FOLDER IS GAVE ME THAT MESSAGES. PLEASE HELP ASAP! THANKS!
Trying to format my sd card on Sony a7 but when I go to the format tab it does not let me click on it and says "this function is disabled"?
Not sure if I'm formatting it the right way or the right setting. I assume it's right since it says "format" but it won't let me get into the setting of it and when I do click it it says "this function is currently disabled". Any ideas?
I have a Moto G3 and it's showing error message that "SD Card removed unexpectedly". Are there any workarounds?
Hi Gonzalo Massa,You can try this steps: Switch your phone off.Remove your SD card.Switch it on again. Confirm whether the SD card has been considered removed by the Android System by checking the Storage setting in SettingsSwitch your phone off again and put the SD Card back inSwitch on and check againIf your device has Marshmallow you can get more information about how to use the SD card in your phone, please click here.Hope It helps,Motorola Support.
How do I fix my micro SD card that became a read-only memory card?
Step 1. Run CMD to remove 'Read Only' from hard disk/USB/SD card/external hard driveIt’s quite simple to remove and fix storage device 'Read Only' error by applying CMD command. The only thing that you shall keep in mind is to be very careful while following below CMD guide steps to remove 'Read Only' error from SD card, USB drive, hard disk or external hard drive.Connect 'Read Only' storage device such as SD card, USB, external hard drive etc with PC;Open Command Prompt by typing: command in Search tab, right-click Command Prompt run as administrator.Type: diskpart and hit Enter;Type: list disk and hit Enter;Type: select disk 0 and hit Enter; (0 shall be the drive letter of your read-only hard drive/USB/SD card etc.)Type: attributes disk clear readonly and hit Enter;Type: exit and hit Enter to finish the process.After this, your storage device shall be accessible again and you can be able to read and use the saved data on your SD card, USB or external hard drive then. If you still cannot access saved data on your storage devices or lost some saved files/documents, don’t worry. Here below in Step 2, you’ll know how to access to your saved data.Step 2. Restore saved data from HDD/USB or external HDD after removing 'read-only'/write-protection errorIf you cannot access the saved data on your storage devices such as SD card, USB drive or external hard drive after removing the 'Read Only' error, don’t worry. Right here we’ll show you how to simply access and restore all saved data from your device with powerful data recovery tool from EaseUS.EaseUS data recovery tool supports you to get data out of inaccessible storage devices, RAW disk and even find hidden files for you with simple clicks. Just free download and install it on your PC and follow below 3 steps to get data back now:1. Connect storage devices such as USB/SD card or external hard drive with Windows PC;Run EaseUS Data Recovery Wizard and select location of your 'Read Only', encrypted or inaccessible storage device
Why won't my sd card load on to my computer?
A lot of things could be wrong. 1. The SD card could be corrupt. If you could view the pictures on your camera, then the card is fine. 2. The drivers for the SD card reader could be corrupt or disable. Go to Device manager (right click my computer, properties, hardware, device manager) and look for the SD reader to make sure the drivers aren't disable or missing. 3. The SD card could be locked. on the side of the SD card there may be a little notch that locks your SD card.
How can you fix a micro SD card which is unable to format or delete files?
In your situation, it seems that most probable cause is that your SD card has been corrupted. However, I would suggest trying the following things :In case your SD Card turns corrupt, follow the steps below to recover your data:Insert the affected SD Card into a Card Reader, and then connect the Reader to your systemClick on the Windows ‘Start’ button and select ‘Computer’Search for your SD card under ‘Devices with Removable Storage’ and make a note of the drive letter assigned to your SD CardAgain click on the ‘Start’ button; go to the ‘Search’ box and type ‘cmd’Right-click on ‘cmd’ and then select the ‘Run as administrator’ optionWith this, command a window will open up to fix damaged memory SD card.6. Next, type in ‘chkdsk’ and then the drive letter corresponding to the SD card, followed by a colon and /f; then press ‘Enter keyThese steps will lead to checking for possible inconsistencies present in the SD Card and fix it by removing the errors. Next, follow the message that prompts7. Finally, check the drive letter allocated to your SD card and verify whether the data files have been recovered or notThere might be other reasons your SD Card turns corrupted. And you are unable to tackle the situation. You have the other choice to get advise from data recovery experts and submit your device for analysis.
Receiving this error: This device cannot start. Code 10. How do I fix this?
Go into Device Manager, delete the device. Reboot the computer. Allow it to find and install the default driver. If no driver is found automatically, THEN run your downloaded driver. Reboot again. Test it. If that fails. Delete the driver again. Open up your computer and disconnect the SD card reader from the motherboard. Reboot the computer. Then turn it off, reconnect the SD reader and boot it up, repeating the first steps I gave you. Let me know if it fails, there are other things to be done in that case. *edit* I didn't ask but are you perhaps running Windows Vista? Ok did a bit or research. Do me a favor and at the run box, type services.msc and then scroll down to look at "Portable Device Enumerator Service" and make sure it's not disabled. If it's in manual, set it for automatic and then reboot. MY problem was I missed the part where you said your CD Rom wasn't working either when you put a disk in.