What stone do I use to take high spots off a metal surface?
I am in maintenance on CNC machines and see many guys using stones to stone the metal surface of say, a motor, before they mount it to make sure there are no high spots and the motor face sits perfectly flat. What type of stone is this they are using? Its pretty small, rectangular, maybe 3-4 inches long, an inch thick, 2 inches high.
Why does Marble feel cool to the touch even though the surface is at room temperature?
When I read your question, I was looking for an answer on internet and I came across http://www.comparerocks.com/en/w...The reason behind this is, the specific heat capacity of marble is quite high and hence it absorbs heat from the ground and surroundings. Marble is a hard stone and has dense structure and hence it becomes easier for marble to absorb heat from warmer objects. This heat dissipates through marble quickly and the marble floor feels cold. The above site provides information about various rocks. You can checkout the site for more information.
How do you get rust stains off porcelain?
This is green cleaning method is efficient, fast and, above all, very economical. Besides kitchen utensils, rust can be found in other places, for example, in a kitchen sink.During use, due to hard water, the surface gradually loses its luster.Usually, rust accumulates in hard-to-reach areas, for example around the tap, or in those corners where moisture usually remains.To prevent this, use this simple recipe.What will be required:Coarse salt (the amount depends on the surface area)½ lemonWhat should be doneTake a lemon and cut it in half. Then apply a little large salt on it. Use lemon as an abrasive sponge.After removing the leftovers from your pan or other utensils, rub it well with a lemon. When you see that the salt has darkened, add a little more.Gradually you will see that the rust goes away. Allow to stand for about 5 minutes and rinse the salt with water.And, finally, complete the cleaning process as well as in the previous case: dry the surface with a paper towel and wipe with olive oil.In case of washing, simply wipe it with a paper towel. It immediately flashes like a new one.
What can I do to remove these stains from granite tile surface?
There are stone cleaning and restoration specialists that are skilled and equipped in cleaning various natural stones found in many buildings, including marble, sandstone, granite and many others. By working with them, not only your granite tile surface will be restored to its original beauty, but the other stone parts of your building as well.
Is it worth hiring a professional to seal granite and stone in new home or do it myself?
Definitely a DIY job -- we did a kitchen remodel recently, and sealing the granite counters was included as part of the install. But as he was applying the sealer, the installer said "You don't really need me to do this. When it's time to reseal, just get the sealer and do it yourself". The process is- -clean and dry the slab -use a clean cotton rag to wipe on the sealer (old t-shirt works great) -let it sit per the instructions -wipe off any excess and buff -keep it dry for 8 hours -you're done
How do you get rid of efflorescence on Pavers/Stones?
My steps were built using Rinox pavers and I've got alot of efflorescence on them. The contractor told me that this was a normal process from the concrete curing process and that it goes away after a short while. It's almost 3 years later and It's still there. Does anyone know if this is going to go away or how to treat it. I find it so unattractive everytime I look at it. Thanks
How to hang a large wreath on stone pillars?
I have two large stone pillars outside of my home that I'd like to hang a large wreath from (on each). Not sure how to successfully do this without doing much/any damage to the pillars themselves. Can someone take a peek at my photos and let me know what I need to pull this off and the best way to do it? Thank You!
How do I get gloss paint off concrete slabs?
I accidentally got some gloss paint on some concrete slabs it has fully dried and will not come off! I have tried using turps, isopropanol alcohol, sand-paper and a jet-wash, nothing works!!! Do you know any ways of getting it off? please!